X

Vous n'êtes pas connecté

Maroc Maroc - SAU.COM.AU - content - 15/Nov 05:45

RB25 S2 Idles but doesn't want to rev

I'm a bit stuck with this one fellas, I recently decided to undertake a turbo conversion on my GTS-4, ended up pulling the motor to replace all the seals and do an mls head gasket and arp head studs while I was at it. Everything has gone according to plan, no oil or coolant leaks, compression checked out, and decided to give it a test before I book it in for a tune As it stands right now, the turbo only has oil lines plumbed so that I don't put boost into my untuned engine, and I'm using the factory GTS-T crossover pipe with a maf and poddy as a temporary intake. The car starts with relative ease and idles amazingly, however as the title suggests it really doesn't want to rev up, runs very smooth but almost feels choked out and unresponsive to the throttle, almost like it's running lean or something? I've triple checked my vacuum lines and timing with a timing light, injectors haven't been touched as of yet to avoid flooding the engine and worked perfectly beforehand, new plugs and coilpacks, I've even unbolted the cat just to see if it spontaneously collapsed, no dice The car currently has a nistune r32 gtst ecu installed so I have no way to check for fault codes. At this point I'm a bit stumped. Is this normal behaviour for a car with a turbo bolted onto the exhaust going nowhere? I'd imagine the turbo wouldn't cause this much restriction in the exhaust without the boost going through the intake. Any ideas? If necessary I can link a video of how it responds to full throttle while in neutral.

Articles similaires

Sorry! Image not available at this time

RB25DET S1 Into R32 GTS-T Assistance Required!!!

sau.com.au - 04/Nov 10:29

Hi All, Ive recently pulled my head in and gotten started on my 2year long project for my R32 RB25 swap, I went into it head high and confident it was...

Sorry! Image not available at this time

GReddy Injector Help!

sau.com.au - 10/Nov 00:13

Hi all, I have a older model of the Greddy Front facing intake on an RB25DET NEO Head. I've bought aeroflows fuel rail and injector kit (1000cc...

Sorry! Image not available at this time

presentation

sau.com.au - 10/Nov 17:40

hello everyone, an RB26, or RB25 project in the medium long term. I don't know much about this engine or turbo engines in general, I'm here to...

Sorry! Image not available at this time

presentation

sau.com.au - 10/Nov 17:40

hello everyone, an RB26, or RB25 project in the medium long term. I don't know much about this engine or turbo engines in general, I'm here to...

Sorry! Image not available at this time

Boost level and torque curve

sau.com.au - 10/Nov 19:20

enjoy the surge of a turbo, it's fun and part of the appeal of these engines. however I always believed that the torque was flat or diminished...

Opinion - "Shove a fork in it, that Championship is done"

hauraki.co.nz - 04/Nov 11:41

Let’s start off by clarifying one thing: I’m a long-time McLaren supporter. 2015 was when I first got into F1, and what a rough year that was for...

Sorry! Image not available at this time

UG graduates celebrate proud moment in their academic journey

kaieteurnewsonline.com - 10/Nov 04:45

In their own words–   “I’m feeling both nervous and excited at the same time. Balancing work with my classes was incredibly challenging, but I...

Sorry! Image not available at this time

R34 power steering

sau.com.au - 08/Nov 20:37

Hi all my r34 has been off for over a year with occasional start. Today I noticed a lot of noise from engine bay when turning the wheel as...

Sorry! Image not available at this time

Thinking of getting a Q50 300hp and just tuning it instead of getting the Q50 Red or 400R

sau.com.au - 05/Nov 14:15

So next year I am looking at upgrading from my VE SS bomadore ute to something more refined. I wanted to stick with a V8 but not anything German...

Sorry! Image not available at this time

One million engines from JCB

timberbiz.com.au - 12/Nov 23:42

JCB has marked a major manufacturing milestone with the production of its one millionth engine. Production started in 2004 at JCB Power Systems in...

Les derniers communiqués

  • Aucun élément